The operation of the offset press must be well lubricated. If the lubrication is poor, it is likely to cause damage to the machine within a few tens of minutes. In severe cases, the machine may even be scrapped. According to the characteristics and working practices of the offset press, I believe that the lubrication should pay attention to the following aspects:
one. Selection of Lubricants 1. As the host part of the domestic sheet-fed high-speed offset press uses a shield to seal off the rain-type automatic lubrication device, the oil pool should be selected medium-viscosity 30-40 lubricants. If the viscosity of the lubricant is too high, it can easily damage the oil pump and block the oil circuit; the viscosity is too low and the lubrication is poor, which is unfavorable to the machine.
2. Select oil No. 50 for other parts of the oil eye and cam. Because the 50th lubricant has a high viscosity and strong adhesion, it will not flow away immediately after refueling, and it can maintain a long time of lubrication, which is good for the machine.
3. The air pump will produce higher temperatures during operation, so it is more appropriate to use No. 50 lubricating oil.
two. Refueling Method 1. Before the new machine is used, it must be properly refueled according to the lubrication requirements of the instructions.
2. In the daily refueling work, the engine oil number should be checked first, and the clean lubricating oil should be added to prevent the oil from blocking and affect the lubrication. In addition, it is necessary to add oil in order to avoid omissions.
3. The refueling must be completed before the machine starts. It is forbidden to add oil during the operation of the machine to prevent the oil bottle from falling into the machine and causing personal and mechanical accidents.
4. In the normal production process, the lubricating device, oil eye, and oil line should be inspected frequently. Found that the fueling device is damaged, lost or oil, oil eye blockage, to repair in time to ensure normal lubrication.
three. Refueling cycle 1. Before the new machine is used, it is necessary to check whether all parts of the oil eye and oil line are unblocked, whether the oil pump works well, and add enough oil according to the lubrication requirements. After 2-3 weeks of use, completely replace the oil in the oil bath once. Afterwards, under normal circumstances, the oil pool should be replenished once every half month to ensure sufficient oil; the oil in the oil pool (including the air pump) should be replaced once every six months. While changing the oil, thoroughly clean the oil sump, oil pump, and transition unit. Check the working conditions of the oil circuit and the oil pump, find out the problem and repair it in time, and do not run sick.
2. Manually refueling is used to expose most of the moving parts of the offset press, the front gauge part and the inside of the wall panel. In general, each shift must be filled twice with lubricant to meet normal lubrication. (North Printing Co., Ltd. Peng Guilin)
one. Selection of Lubricants 1. As the host part of the domestic sheet-fed high-speed offset press uses a shield to seal off the rain-type automatic lubrication device, the oil pool should be selected medium-viscosity 30-40 lubricants. If the viscosity of the lubricant is too high, it can easily damage the oil pump and block the oil circuit; the viscosity is too low and the lubrication is poor, which is unfavorable to the machine.
2. Select oil No. 50 for other parts of the oil eye and cam. Because the 50th lubricant has a high viscosity and strong adhesion, it will not flow away immediately after refueling, and it can maintain a long time of lubrication, which is good for the machine.
3. The air pump will produce higher temperatures during operation, so it is more appropriate to use No. 50 lubricating oil.
two. Refueling Method 1. Before the new machine is used, it must be properly refueled according to the lubrication requirements of the instructions.
2. In the daily refueling work, the engine oil number should be checked first, and the clean lubricating oil should be added to prevent the oil from blocking and affect the lubrication. In addition, it is necessary to add oil in order to avoid omissions.
3. The refueling must be completed before the machine starts. It is forbidden to add oil during the operation of the machine to prevent the oil bottle from falling into the machine and causing personal and mechanical accidents.
4. In the normal production process, the lubricating device, oil eye, and oil line should be inspected frequently. Found that the fueling device is damaged, lost or oil, oil eye blockage, to repair in time to ensure normal lubrication.
three. Refueling cycle 1. Before the new machine is used, it is necessary to check whether all parts of the oil eye and oil line are unblocked, whether the oil pump works well, and add enough oil according to the lubrication requirements. After 2-3 weeks of use, completely replace the oil in the oil bath once. Afterwards, under normal circumstances, the oil pool should be replenished once every half month to ensure sufficient oil; the oil in the oil pool (including the air pump) should be replaced once every six months. While changing the oil, thoroughly clean the oil sump, oil pump, and transition unit. Check the working conditions of the oil circuit and the oil pump, find out the problem and repair it in time, and do not run sick.
2. Manually refueling is used to expose most of the moving parts of the offset press, the front gauge part and the inside of the wall panel. In general, each shift must be filled twice with lubricant to meet normal lubrication. (North Printing Co., Ltd. Peng Guilin)
Advantages of charcoal barbecue:
Big fans of charcoal Stainless Steel Bbq Grill will never choose a gas barbeque. They do have a point: charcoal ovens can reach a ferocious 482 degrees Celsius on the surface of meat, much hotter than standard gas ovens without infrared burners. Using this heat allows the skin of steak and lamb chops to turn into our beloved pastry, while maintaining the red and pink color inside the meat.
Another major advantage of charcoal roasting is smoke, an interesting by-product of burning. Charcoal smoke contains a wide range of flavor molecules, especially when ignited. Gaseous fuels are simple molecules (CH4 is natural gas, C3H8 is liquid propane). If they were completely burned, there would be only water and carbon dioxide, no flavor. In order for a gas oven to produce smoke, wood must be added. When the fat and juice of food drips onto the burning charcoal, a great deal of smoke is produced. If there is only a brief encounter with smoke, it does not significantly alter the flavor of fast-cooking foods such as hot dogs, beef burgers, or even lean steaks. In thick cuts of steak and chicken, the flavor produced by the smoke can be clearly perceived. There is a noticeable difference in flavor if you use your corten steel bbq for a long, low smoke roast. The flavor of the smoke produced by the gas oven is very simple.
| Name | Outdoor gas grill corten steel metal barbecue |
| Material | Corten steel |
| Cooking plate Size | Diameter 1000mm |
| Base Size | 500*500*700mm |
| Thickness | Base:2mm, Cooking plate:10mm |
| Weight | 120KG |
| Packing | Pallet/carton/wooden box packing |
Packing
Packing will by pallet/carton/ wooden box,according to different demand.
Gas Bbq Grill,Propane Grill,Gas Barbecue,Natural Gas Grill
Henan Jinbailai Industrial Co.,Ltd , https://www.hnjblfirepit.com