[ China Wardrobe ] After repeated comparisons, we finally selected our own wardrobe , but if we want to use the wardrobe more smoothly and extend the service life, then the installation process of the wardrobe is very important. Today, Xiaobian will bring you detailed explanation of the installation steps of Yilian wardrobe, giving you the best quality wardrobe.
Yi love wardrobe installation steps
1. Use a mat to place the floor. Start by assembling the wide side panel against the end of the wall. Place the wide side panel on the ground (maintain 700mm away from the rear wall). First, put the plate of the filled three-in-one rubber plug on the cloth, check the hole spacing and the drawing, and install the three-in-one single-link. Then the solid layer is nailed to the cork, fixed on the wide side plate, the top handle with the large handle hole facing upward, the other solid layers are facing downward, and the foot line large handle hole is facing inward (the middle solid layer is consistent with the L frame height, that is, the bottom plate to the solid layer The inner space is 960mm, and the hole is drilled on site.) Put the side panels, nail the cork, and the cork is required to connect the solid layers on both sides. Install the double connecting rod on the second cabinet. Note that the large handle on the double connecting rod can only lock half, that is, 90°. When the two solid layers are fixed to the side plates, tighten the large handles at the same time. Repeat the installation steps for the second cabinet when installing the third cabinet.
2, nail back board. Place the assembled whole cabinet on the floor of the point cloth, and lay the side panels in the same plane. Use a slider to measure the diagonal size of the cabinet and adjust it to the same level. Start with the first backing plate from the wide measuring board. Note that if there is a solid nail in the middle, draw the center line of the solid layer with a pencil and nail it. nail.
3. Installation of the L frame. Use the side plates of the L frame to have a parallel line on the corresponding side plates, then move the center line of the three-in-one rubber particles up by 9 mm, and draw a parallel line on the corresponding bottom plate with the top frame of the L frame. The inner center 9mm draws the center line of three rubber pieces. The hole was drilled with a 10 mm drill bit and the hole depth was 10-20 mm. Install a single pole. After the L frame is installed, nails are fixed on the back plate.
4, clean the wardrobe installation debris, left and right station one person, the wardrobe is slightly inclined backwards, forcefully lifted, moved back to the desired position, pay attention not to scratch the floor, the wall.
5. Installation of push-pull mirrors. The three-section rail is mounted on the push-pull mirror, and the height of the push-pull mirror is generally 1700 mm above the bottom solid layer (customer can request height). The rail transverse line is drawn on the side panel at a height of 90° according to the required height. The parallel distance between the new eyes in the three-section track on the upper line is measured, and accurate data is obtained. The lower track transverse line is drawn on the side plate with a 90° angle. Install the upper and lower mother rails of the push-pull. The mother rail is 5mm away from the backboard and is equipped with a push-pull mirror.
6, the installation of Yitong. Move the 38mm draw cross-cut line from the ground level, the side plate is divided into the vertical cut line, and the cross pad is the center position of the first eye above the clothes pass.
I believe that through this article, you must have some understanding of the installation steps of the Yilian wardrobe. If you encounter the wardrobe installation in the future, you can also take a look at it yourself to avoid mistakes.
Patio dining chair set featuring full-scale comfort, you can stack and store, you can set up instantly for guests. The sturdy chairs are woven with all-weather PE rattan fibers that is hand weaving one by one, very beautiful, and stack for convenient storage.
Patio dining chair set has many options: armchair and armless chair, you can decorate different round, square or rectangle dining table. You can be free collocation by yourself.
About us:
1.our factory is more than 20000 square meter big.
2. Our showroom is about 800 square meters.
3. we have professional sale team and more than 200 workers.
4. The capacity of our factory is 60 containers/month.
5. we attended CIFF furniture fair and canton fair.
Welcome your inquiry for further discussion.
Dining Patio Chair Set,Rattan Dining Chair Set,Wicker Dining Chair Set,Outdoor Dining Chair Set
Golden Eagle Outdoor Furniture Co., LTD. , https://www.gepatio.com